Shop – Gold Stars Medical

1. Platform Switching Platform switching helps to minimize bone loss that can reduce peak-stress and thereby preserve marginal bone Helps to establish a certain biological width of the peri-implant mucosa

2. Smooth Shoulder A smooth surfaced fixture shoulder helps ensure immediate insertion depth Allows easy bone profiling at 1st, 2nd surgery

Details

DENTIS OneQ

Designed for High Initial Stability Double tapered implant body (Regular & Wide), straight body & tapered head design may allow easier depth control and stable primary fixation Cutting groove boosts self-tapping ability and enables a smaller osteotomy which may help achieve earlier stability

S.L.A Surface for Faster Osseointegration

200% enhanced surface area compared to RBM surface
Effective osseointegration
Lower level of residue

Details

DENTIS SQ

Simple Placement & Strong Osseointegration

High Initial Stability

Tapered design
Dual & open thread

Smoother Insertion

3-blade and wide cutting edge

Easy Depth Control

Fixture length (8-14mm) : 0.5mm shorter than the written length

Details

ROOTT K

One-piece implant for excellent stability in lateral alveolar walls & soft bone.

Single unit, mechanically strong
Cutting stands, cortical fixations
Bending up to 15 degrees

Details

ROOTT S

One-piece implant for multiple unite screw-retained restorations with a narrow screw

Fully screw-retained prosthetic options
Ideal for narrow ridge area
Bone condensation design
Free multifunctional part

Details

ROOTT M

One-piece implant for multiple unite screw-retained restorations with a wide screw

Fully screw-retained prosthetic options
Strong & secure fixation screw
Bone condensation design

Details

ROOTT B

One-piece implant for residual alveolar ridge atrophy with bendable neck & polished body

Excellent protection from inflammation
Adjustable abutment slope angle
Easy placement in a socket
Ideal for resorbed ridges
No pumping effect

Details

ROOTT CS

One-piece implant for single & multiple unite cement & telescopic restorations

Simple placement & prosthetic procedure
Bone condensation design
No pumping effect
Short neck for use in a limited areas

Details

ROOTT C

One-piece implant for single & multiple unite cement & telescopic restorations with bendable neck

Simple placement & prosthetic procedure
Adjustable abutment slope angle
Bone condensation design
No pumping effect

Details

ROOTT R

Two-piece implant with self-tapping thread

Excellent primary stability
Free multi-functional part
Conical connection
Extra thin & strong

Details

Medibrex Teebone Biphasic Bone Graft

Teebone is an osteoconductive alloplastic material designed for bone substitution. Its biphasic nature allows a controlled resorption profile similar to human bone. Due to its composition, 75% Hydroxiapatite and 25% Beta tricalcium phosphate, Teebone regenerates new bone through two different stages of activation. The breakdown of B-TCP by the osteoclast will free ions that enhance bone grow, while the hydroxyapatite acts as support for the bone ingrown whiting the graft, being slowly substituted.

Details

COLLA-D KOLAJEN MEMBRAN

Colla-DM is purified bovine collagen type I derived from bovine of BSE free zone authorized by OIE. Product Features: 1) Adhesive property & Flexibility - Easy manipulation and placement - High hydrophilic property and excellent flexibility 2) Multiple-Layered Structure - Effective bone & tissue regeneration by securing enough space maintenance - Facilitating proliferation of osteoblasts 3) Safety: - Derived from bovine of BSE (Bovine Spongiform Encephalopathy) Free zone authorized by OIE (Office International Des Epizooties) Resorbtion Period: 3-6 months Indications: Sinus Lift / Ridge augmentation / Fenestration defects / Horizontal augmentation / Alveolar ridge reconstruction / Dehiscence Available sizes: (Soft and Hard Type) 1) Soft Type 10x20 mm 15x20 mm 20 x 30 mm 30 x 40 mm 2) Hard Type 10x20 mm 15x20 mm 20 x 30 mm 30 x 40 mm Medpark is the products of the Republic of Korea Medpark has the largest manufacturing facility in the Asia-Pacific which is producing completed product line of Bovine, Porcine, and Allograft bone.

Details

Medpark Bone D

Description Bone-D XB (Bovine Xenograft) is manufactured by sintering technology (High Temperature) of Medpark so it is very good property in term of strength, porosity, and safety (BSE Free). Bone-D XB is combined biocompatible and safety-proven materials to maximize convenience and quality during the surgery. Bone-D XB has similar structural characteristics with human bones. Due to its high porosity, Bone-D XB provides the most optimal environment for promoting osteoblast adhesion, blood vessel formation, and bone regeneration. Key Properties: Grain Size : 0.5 - 1.0 mm 1) Excellent Pore Struture - Manufactured by sintering technology of MedPark > Securing strength / porosity / BSE Free - Extensive internal area - Maintenance of ideal volume 2) Easy Manipulation - Faster absorption by blood and saline for its porosity - Applicable to various indication such as Socket Preservation, Sinus Lift, Periodontal Defects and Ridge Augmentation 3) High Wettability - Stimulating new bone formation with great hydration with blood - Osteoblast in blood helps the new bone formation Indications: - Dental implant surgery - Socket Preservation - Periodonal Defects - Sinus lift - Ridge Augmentation - GBR cases

Details

TITMUS V2 AND V4

Designed for accurate and reliable vision screening, the V4 and V2 portable vision testers provide a comprehensive range of tests and features that can minimise consultation times, improve workflows and improve record keeping. Visual acuity (near, far and optional intermediate), depth perception, colour perception, phoria, and peripheral tests can all be completed in a very efficient and accurate manner. The Titmus V4 can also provide night vision testing should your screening programme require this type of testing.

MAIN FEATURES:

Compact and portable
Ergonomic
Head sensor for accurate head positioning
Remote control panel
True colour testing
Comprehensive range of test parameters
Night vision tests (V4)
No calibration required
Ideal for industrial and DSE screening needs

Details

OPTEC 5000P & 5500P

A portable dual lens (near and far) vision tester with a remote-control panel that can measure visual acuity, depth perception, colour vision, lateral and vertical phoria and peripheral vision. Standardised test slide kits are available to meet the needs of industrial and primary care organisations. For specialist needs, there is a library of over 150 test slides available.

MAIN FEATURES:

Ideal for industrial and DSE screening needs
Dual lens system for testing bifocal patients
6/4.5 (20/15) to 6/60 (20/200) visual acuity range
Unique maintenance free LED lighting system
Portable
No calibration required

Details

VT1 MASTER & VT1 MASTER GT

The latest addition to our vision testing range, we are proud to introduce the VT1 Master & VT1 Master GT as the future in occupational vision screening. The VT1 Master and VT1 Master GT are designed to be easily connected and controlled by your PC. This helps reduce test times with efficient process control as well as data management. These vision screeners offer a wide range of regular test options to help create fully customisable test routines such as monocular vision and visual acuity, depth perception, colour, phoria and peripheral vision tests. These screeners also feature a broad spectrum of additional tests such as astigmatism, night vision, landolt rings, amsler, hyperopia tests and central visual field test.

MAIN FEATURES:

PC operated
Customisable patient instructions
Time-saving test routines
Horizontal and vertical peripheral field tests
EMR connectivity
Glare sensitivity and resistance

Details

PULMOSCAN

Quick, effort-free airway impedance testing. The PulmoScan is the world’s first portable, stand-alone, and wireless Forced Oscillation Technique (FOT) device, FDA cleared for both clinic and home use.

FEATURES

FAST, ACCURATE, LOW-COST Pulmonary Testing
OSCILLOMETRY METHOD
SIMPLE -The patient breathes normally (tidal) into a mouthpiece, that’s it.
Fast – Each test run takes about a minute
Safe – Low-frequency sound waves to measure lung function, shown safe for children as young as 4 years old
Accurate – Based on forced oscillation technique (FOT), which is clinically validated in various studies
PulmoScan Brings Pulmonary Testing Closer to Patients
Pediatric Clinics
Primary Care Clinics
Mobile Testing
PulmoScan is Designed for the Mobile Generation

TABLET APP

Simple interface of our Mobile App makes it easy for anyone, anywhere, to use PulmoScan.
Select reference equations to compare patient results.
Pre and post bronchodilator test comparison
Detailed reports
App and cloud functions for remote monitoring

Details

NOMAD- PORTABLE SLEEP LAB

MAIN FEATURES

Color coded sensors and receptacles to ensure easy patient hook up.
Recording that starts with a valid pulse oximetry signal.
Ability to monitor and initialize via wireless Bluetooth connectivity.
Download files via USB interface in minutes.
Rapidly autoscore with the Polysmith world-renowned scoring algorithm.
Schedule HST patients on DMS calendar.
Initialize recorder from calendar or Polysmith interface.
Auto-configure Polysmith for analysis by the type of recorder being used (Type II or Type III) when recording is loaded.
Store recorder Type (I, II, III) with each study for easy query
View live data on Polysmith acquisition screen
Standard or Custom reporting for any
Type (I, II, III) of recording

Details

N2 Washout Lung Volume Measurement

N2 Washout Lung Volume Measurement is a technique for determining the uniformity of gas distribution in the lungs as well as the behavior of the dependent airways. Works based on the technique of washing N2 out of the lungs, during that time the patient breathes 100% O2 using dilution properties of gases.

The patient breathes 100 percent oxygen, and all the nitrogen in the lungs is washed out.
The volume of exhaled air and the nitrogen concentration in that volume are measured.
The difference in nitrogen volume at the initial concentration and at the final exhaled concentration allows a calculation of intrathoracic volume, usually FRC.

Details

Gas Exchange Analyzer

MediPines AGM100® – Pulmonary Gas Exchange Analyzer Revolutionary, non-invasive respiratory assessment and monitoring system.

Calculated Arterial PaO₂ blood gas levels in under 2 minutes
Simple push-button respiratory impairment detection
Clinically actionable information to guide better treatment

Respiratory Parameters

O₂Deficit, gPaO₂, PAO₂, PETCO₂,
P/F ratio, SpO₂, respiratory rate, & more

Details

CHEST WALL OSCILLATOR – CAREWAY

CAREWAY is High-Frequency Chest Wall Oscillator (HFCWO) from Korean manufacturers. This medical device helps to maintain lung and airway clearance by helping to discharge airway secretions such as sputum and mucus that are deep in the capillary bronchioles or bronchioles by vibrating the chest wall rapidly using a high-frequency pulse. CAREWAY is designed with the heart of parents who pat their sick children on the back. Therefore, it can be used safely by children, the elderly, and adults. It has been used mainly in an intensive care units (ICU), respiratory internal medicine, rehabilitation center, and home care.

Details

SPIROLAB – ALL IN ONE DESKTOP SPIROMETER

MAIN FEATURES

Portable, Desktop and PC-Based Spirometer, with Optional Oximetry
7-inch Touchscreen, all-in-one Spirometer with embedded printer and Optional Oximetry
Real-time test also available on PC, via USB and Bluetooth.
Perfect suite in Hospitals and Asthma camps, with its fast and silent built–in thermal printer with customizable printout format.
Lightweight for easy mobility, carrying case included, long life Rechargeable Battery.
GLI predicted sets available in Stand-Alone mode and PC mode.
Pediatric Incentive available on display, to improve patients’ compliance during the test.
REAL-TIME TEST Spirometry: FVC, VC, MVV, PRE/POST Bronchodilator comparison, Oximetry (optional): Spot test (SpO2, Pulse)
CARRY EVERYWHERE– LCD 7″; Display, long battery life, large internal storage and comes with carry bag.
PC CONNECTION– real time test on PC screen, connect with your EHR/EMR, back-up internal memory, etc
COMPLIANCE WITH ATS/ERS 2019 And other Standards including ISO 26782 (for Spirometry), ISO 23747 (for PEF), ISO 80601-2-61 (for Oximetry), and more
PREDICTED SETS AND PREDICTED VALUES- Large Selection of Predicted Sets (including GLI) and Predicted Values (including comparison %Pred, Z-score and LLN) in stand-alone mode
EHR CONNECTIVITY-Via PC, integration with patient database on your EHR/EMR (in HL7, GDT)
CALIBRATION SOFTWARE EMBEDDED-Available on device, with printable calibration report (no separate software required)
PRINTER EMBEDDED-Thermal printer. Paper size 112mm

Details

AIRWAVE OSCILLOMETRY (AOS/FOT) SYSTEM

MAIN FEATURES

Tidal Breathing- No forced expiration.
Respiratory Mechanics- Info related to small airways.
Fast & Easy-Test in a few minutes.
Adult & Pediatric-Normative values provided.
Intra-Breath Analysis-Pattern & Time-Course.
Easy Daily Calibration-Less than 30sec.
Compact & Portable-Weighs only 700 g.
Pre/Post Testing-Automated Workflows.

Details

SMART PFT NEBULIZER

Compressor unit

No need for an external source of compressed air, a low noise compressor is built in.
A comfortable, safe and very robust device to support challenge testing.
The compressor runs fully automatic.
A built-in panel computer with LCD-display guarantees a very simple control handling.

Details

CUSTO HOLTER ABPM

COMBINED RECORDER FOR SIMULTANEOUS MEASUREMENTS OF HOLTER ECG AND AMBULATORY BLOOD PRESSURE

Simultaneous saving of ABPM and Holter ECG
Wireless ECG recording with custo belt and custo guard
Higher patient comfort due to low-noise operation
Blood pressure adapted pump regulation for patient-friendly measurement
High safety due to double pressure relief valve
Skin-friendly, easy-to-disinfect cuff in sizes S – XXL
Wireless data transfer from the recorder to the PC
Precise measurement even with atrial fibrillation
Perfect for the measurement of central blood pressure (only custo screen 310)
Automatic day and night recognition
Validated according to the new requirements of the European Society of Hypertension

Details

CUSTO WATCH

WIRELESS HOLTER ECG WITH CHEST BELT AND 3-CHANNEL ECG TRANSMITTER

Wireless ECG recording with custo belt and custo guard
Up to 72 hours recording time
Continuous recording of 3 channels for clear rhythm analysis with detailed ECG view
Check of signal quality for all ECG channels
High wearing comfort and extremely lightweight
Adjustable patient display
Exchangeable bracelets in various sizes and colours
Energy-saving wireless transmission of ECG signal

Details

CUSTO CARDIO-400

FACTS CUSTO CARDIO 400

Perfect data transfer via USB and Bluetooth
“2 in 1” ECG with integrated suction unit
Mobile application
Sampling rate up to 32 kHz for a higher resolution and improved pacemaker detection
Defibrillation protection dielectric strength 5000 V (recovery time < 10s>
Suction capacity 6 steps, 0 – 280 mBar (in 40 mBar steps)
custo true wave® filter

Details

SOL Soft Tissue Diode Laser by DenMat

SOL® Desktop dental laser delivers true portability, power and precision. It features enhanced ergonomics, a simple interface, and a high-contrast aiming beam designed to make laser dentistry easier than ever. The cost effective diode laser designed for the entire team to deliver outstanding performance at an unbeatable value.

Details

Dental Milling Machines Vhf K4 edition

The extremely compact design of the K4 edition is a real eyecatcher. A closer look at the four-axis dry milling machine reveals its rigid structure. This ensures first-class results – even when working with extremely hard cobalt-chromium-based NEM materials.

Details

ZYRCOMAT 6100 MS Sintering Furnace

Developed and manufactured entirely in Germany, the VITA ZYRCOMAT 6100 MS delivers the quality and reliability that you have come to expect from VITA. The sintering furnace offers a choice of three sintering modes: HighSpeed, conventional and user-defined, giving you flexibility at all times. Optimized for use with VITA materials, as well as with all commercially available ZrO2 and Al2O3 ceramic dental framework materials, this high-temperature sintering furnace sets the pace in terms of user orientation and ergonomics. An LED light bar and freely-adjustable acoustic alerts, reliably provide information on firing progress even across longer distances. The ventilation system is cleverly designed so that rising heat is safely routed away from the electronics, ensuring long-term protection of the heating and electronic elements.

Details

AutoScan DS EX Pro (H) Desktop Scanners

AutoScan-DS-EX Pro (H), developed and manufactured by SHINING 3D, is a 3D dental scanner with powerful functions for multiple applications covering scans of impressions, plaster models, articulators, implant abutments, etc. Its high-resolution cameras, advanced algorithms, and user-friendly interface bring you with superior data quality with optimal experience.

Details

Dental Milling Machines Vhf Z4

Comes with full factory guarantee and has been checked and revised by VHF before offering for sale. The unit has only been used to demonstrate our now famous workflow and is offered at competitive pricing as it’s not brand new but as good as new.

Details

NextDent 5100 LC-3D PrintBox UV Post-Curing Unit

The LC-3DPrint Box is a revolutionary UV light box, suitable for post-curing 3D printing materials. The new LC-3DPrint Box is equipped with 12 UV light bulbs strategically placed inside the box. This ensures that a product is illuminated from all sides, which results in a quick and uniform curing cycle. The spacious interior (ø 26 cm, H 19,5 cm) allows you to easily cure multiple products at once. In addition, the box has enough space to place an articulator inside. If necessary, the UV light bulbs can be changed easily. Light-based UV post-curing unit specially designed for post-curing 3D printing materials (includes initial set of lamps)- Add power cord per unit

Details

AccuFab L4D Dental 3D Printer 3D Dental Printers

The AccuFab-L4D/L4K’s high fidelity of print result brings extraordinary digital dentistry workflow from intraoral scanning to rapid 3D printing.

Details

Dental Milling Machines Vhf K4 edition

The extremely compact design of the K4 edition is a real eyecatcher. A closer look at the four-axis dry milling machine reveals its rigid structure. This ensures first-class results – even when working with extremely hard cobalt-chromium-based NEM materials.

Details

MAIN FEATURES:

MAIN FEATURES:

MAIN FEATURES:

FEATURES

TABLET APP

MAIN FEATURES

MAIN FEATURES

MAIN FEATURES

COMBINED RECORDER FOR SIMULTANEOUS MEASUREMENTS OF HOLTER ECG AND AMBULATORY BLOOD PRESSURE

WIRELESS HOLTER ECG WITH CHEST BELT AND 3-CHANNEL ECG TRANSMITTER

FACTS CUSTO CARDIO 400

Title

Get in touch with our team

Contact

Office